| Hardware Specifications | |
|---|---|
| Copper Ports | 5 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports |
| SFP Port | 1 100/1000BASE-X SFP ports |
| Connector | Removable 6-pin terminal block Pin 1/2(+/-) , 3/4(+/-) for PV panel (In parallel); Pin 5/6(-/+) for battery charging and discharging The PV input is compliant with DC input but cannot be connected simultaneously with solar input to prevent damage to the device. |
| DIP Switch | Front Panel: Alive Check: All PoE ports enable PD Alive check function. VLAN: Port isolation Extend: Long distance PoE switch. Rear Panel: PWR: Equipment power switch BAT: Battery type switch BV: Battery voltage switch LiFe: Lithium iron phosphate switch |
| Power Requirements | Supports 20-27V solar panel input (open circuit voltage) with 12V battery, maximum solar panel input power of 405W, and maximum circuit 15A. Supports 32-45V solar panel input (open circuit voltage) with 24V battery, maximum solar panel input power of 675W, and maximum circuit 15A. |
| Charging Function | Integrated automatic charging and discharging, maximum efficiency 98%, maximum charging current 15A Integrated battery protection function Integrated battery float charging function Supports over-temperature protection function |
| Battery Type | Based on Full Loading power consumption: 12V / 24V lead-acid battery, maximum charging current 15A 12.6V/25. 2V lithium battery, maximum charging current 15A 14.6V/29.2V lithium iron battery, maximum charging current 15A Note: Recommended capacity 500AH in fully power 120W usage |
| Power Consumption/ Dissipation | 3 watts, 10.2BTU (Standby without PoE function) 140 watts, 477 BTU (Full loading with PoE function) |
| Dimensions (W x D x H) | 142 x 197 x 34 mm |
| Weight | 820g |
| LCD Monitor (W x D) | 26.77 x 16 mm, 1.1-inch |
| Temperature Sensor | Temperature Detector -20 ~ 120 degrees C Humidity Detector 0 ~ 100 % RH |
| ESD Protection | ±8KV air gap discharge ±4KV contact discharge |
| Surge Immunity | 2KV |
| Enclosure | IP30 metal case |
| Installation | Desktop/Wall-mount ear |
| LED Indicators | Front Panel: System: Green: PWR ,BAT.out,BAT.in Per 10/100/1000T RJ45 Port: (Port 1~Port 3): Green: LNK/ACT (10/100/1000Mbps) Amer: PoE-in-use Per 10/100/1000T RJ45 Port: (Port 4~Port 5): Green: LNK/ACT (10/100/1000Mbps) Amer: 1000Mbps Green: PoE-in-use Per SFP Port: (Port 6): Green: LNK/ACT (100/1000Mbps) Rear Panel: System: Green: SYS, PWR, PV in Battery: Green: BAT.out, BAT.in, BAT.V in |
| Switching Specifications | |
| Switch Architecture | Store-and-Forward |
| Switch Fabric | 12Gbps/non-blocking |
| Switch Throughput | 8.92Mpps@64 bytes |
| MAC Address Table | 2K entries |
| Shared Data Buffer | 2.5Mb |
| Jumbo Frame | 10K bytes |
| Power over Ethernet | |
| PoE Standard | IEEE 802.3at Power over Ethernet PSE |
| PoE Power Supply Type | End-span |
| PoE Power Output | Per port 48V DC, max. 35 watts |
| Power Pin Assignment | Port 1: 1/2 (+), 3/6 (-), 4/5(+), 7/8(-) Ports 2~5: 1/2 (+), 3/6 (-) |
| PoE Power Budget | Maximum 120W (depending on power input) |
| Standards Conformance | |
| Regulatory Compliance | FCC Part 15 Class A, CE |
| Standards Compliance | IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3ab 1000BASE-T Gigabit Ethernet IEEE 802.3z Gigabit SX/LX IEEE 802.3x Flow Control and Back Pressure IEEE 802.3at Power over Ethernet Plus IEEE 802.3az Energy-Efficient Ethernet |
| Environment | |
| Operating | Temperature: -20 ~ 65 degrees C Relative Humidity: 5 ~ 95% (non-condensing) |
| Storage | Temperature: -40 ~ 70 degrees C Relative Humidity: 5 ~ 95% (non-condensing) |




